Glorysteelwork

  Individual rail pads suppliers from China the rail pads refer to a pad made of rubber, which is arranged between the steel rail and the lower part of the concrete rail for insulation and shock absorption. To make up for the lack of concrete rigid material, when the rail is installed on the gasket-called soft mounting-this helps to ensure that the stress distribution between the crane wheel and the rail and between the rail and the fixed surface is more even. Individual rail pads are designed for soft-mount installations where rails are laid on intermittent supports. individual rail pads INSTALLATION INSTRUCTIONS: The rail pad should be narrower than the rail it is supporting (nominally 5mm). The pad is normally supplied in 12-meter lengths. The flutes of the pad are placed facing upwards. The pad may be cut to the precise length of the rail. It can be cut with a hacksaw or jigsaw. No installed length of the pad should be less than the spacing between three pairs of crane rail f...

  1220 rail clips /7220 rail clips supplier from China Gloryrail is a 7220  rail clips supplier  from China (it is equivalent to Gantrail 1220 rail clips ), it is a kind of  welded base fixing clip  with double bolts. designed to fix heavy rails. It can withstand a horizontal force from the rail of 300kN(30.6 tonnes). its low profile allows it to be used with cranes that are fitted with guide rollers. 1220-rail-clips-drawing Save The proven design has been used successfully for many years throughout the world. • The clip is welded to the rail support. No access is required from below. • The two main parts are locked together on tightening the grade 10.9 bolts. • The clip has a self-tightening mechanism. • A special vulcanized rubber block applies a controlled force to the rail. Weldable clips are available in different sizes and capacities to suit different rail profiles and wheel loads. The correct clip selection not only depends on those dimensional and mechan...

  Steel soleplates for crane rail The steel soleplates are the medium between the steel plate and the foundation, which can effectively solve the various problems caused by the direct laying of the steel rail on the ground and the subsidence of the foundation. At the same time, it is also the fixed foundation of the track pressure plate. The steel soleplates can be continuous or individual. It is equipped with adjusting bolts, if the crane track system starts to move beyond the operating tolerance, it can be re-leveled or re-aligned in the shortest downtime. GloryRail supplies different size steel soleplates for crane rail installation. We could offer the plate with or without clip base plate welding. steel-soleplates In order to better serve the different needs of customers, our technical team is available to provide advice and support, helping every customer to optimize their rail selections to minimize life cycle costs. We supply suitable rail parts, like fish plates, rail clip...

  1116 rail clips supplier from China Gloryrail is 7116  rail clips supplier  from China (it is equivalent to Gantrail 1116 rail clips ), it is a kind welded base fixing clip. designed to fix heavy rails. It can with satand a horizontal force from the rail of 130kN(13.3 tonnes). its low profile allows it to be used with cranes that are fitted with guide rollers. 1116 rail clips Save The proven design has been used successfully for many years throughout the world. • The clip is welded to the rail support. No access is required from below. • The two main parts are locked together on tightening the grade 10.9 bolt. • The clip has a self-tightening mechanism. • A special vulcanised rubberblock applies a controlled force to the rail.

  WJKC Rail Clips Supplier from China Gloryrail is a WJKC rail clips supplier from China, we could offer two types of rail clips, namely bolted clips and welded rail clips. WJKC rail clips are welded rail clips, also known as track clamp, is a fastener used to fix rails during rail laying. It is also a welded rail fixture and is a widely used crane beam rail fixing standard. WJCK rail clips supplier Instructions for use of the WJK welded rail press: steel plates need to be pre-embedded for foundation construction, the 3 sides of the base are welded to the pre-embedded steel plates, the upper cover is against the edge of the rail, the bolts and the shaft are adjusted to control the pressure and tightness. Install one set on each side of the rail, and the rail needs to be fixed with a pair of rail clamps every 600mm or 500mm

  Crane rail pads supplier from China Gloryrail is a crane rail pads supplier from China, we could offer two types of crane rail pads for continuously supported rail and discontinuous mounting. Individual Rail Pad and Continuous Rail Pad crane rail pads crane rail pads are made of rubber as the main raw material, scientific formula, and high-tech production technology. The rubber pad meets the railway speed-up and environmental protection requirements, and the use of it can improve the transportation capacity of the locomotive. The production and promotion of rubber pads has completely changed the old and backward paving materials such as asphalt, slate, steel plate and so on that have been used for a long time at railway level crossings. It has changed the backward state of uneven crossings, frequent accidents, and frequent maintenance. Laying, its beautiful environmental protection, quick installation and practicality, and solid and solid safety are gradually emerging. Pressure...

  MK7 rail pads supplier from China Mark7 rail pad is a kind of steel-reinforced resilient pad for continuous rail support. A stable crane rail system has three key ingredients: 1. Resilient Pad 2. High strength, adjustable clips 3. Quality rail welding So rail pad is very important in project construction. MK7 rail pads have steel strips inside and grooves on pads, it has good strength and force of friction. Normally the length of the Mark 7 rail pad is 12 meters, we also could offer a special length to suit customer specifications. mk7 rail pads INSTALLATION INSTRUCTIONS: Rail pad should be narrower than the rail it is supporting (nominally 5mm). The pad is normally supplied in 12 metre lengths. The flutes of the pad are placed facing upwards. The pad may be cut to precise length of rail. It can be cut with a hacksaw or jigsaw. No installed length of pad should be less than the spacing between three pairs of crane rail fixing clips. Before installing Mark 7 pad, the supporting a...

  3124 rail clips supplier from China Gloryrail is a 3124 rail clips supplier from China, we could offer two types of rail clips, namely  bolted clips  and welded rail clips. 3124 is a kind bolted rail clip. 3124/20 adjustable crane rail clip is designed to fix the largest rails in the most arduous applications. It can withstand a horizontal force from the rail of 125kN (12.7 tonnes). Its low profile allows it to be used with cranes that are fitted with guide rollers. We use 3124 rail clips in many crane installation projects, it can fix rail on the beam by short bolts, or into the concret with anchor bolts. 3124 rail clips installation • The proven design has been used successfully for many years throughout the world. • The clip is bolted to the rail support. • The two main parts are locked together on tightening the nut. • A special vulcanised rubber block applies a controlled force to the rail. In order to better serve the different needs of customers, our technical te...

  Railroad tie plate supplier from China The railroad tie plate is also called the rail base plate or the soleplate, which is the main component of the crane track or track support system in railway construction. It is also one of the important components in the track structure and plays an important role in damping the wheel-rail power system. With the development of heavy-duty railway transportation, the axle load is increasing day by day. While the rails are gradually heavier, higher requirements are put forward on the performance of the backing plate, and the backing plate is required to have good vibration damping performance, impact resistance, and long service life. The rail tie plate is not only used to support the rail but also to fix the entire rail fastener system. The rails are fixed to the iron backing plate by bolts or spikes to transfer the load of the rail and part of the load to the sleepers while ensuring the stability of the rail system. railroad tie plate instal...

  BS80A Fish plates for Railway Rails Glory Rail  can supply BS standard fishplates joint bars for railway rails for rails connection.  BS80A rail fishplate  is the joint bar used for the connection between BS80A standard rails. We customize the rolling mold of BS80A fish plates. So we could manufacture BS80A rail joint bars in a short time. In addition, we have the experience that producing BS100A rail plates. we supply matched bolts, nuts, and washers. Advantages: Long service life Fast and easy installation Specification: BS Standard Fishplates for Railway Rails bs80a fish plates …….. BS Standard Fishplates for Railway Rails (BS47-1:1997) Specifications Length of 4-bolt fishplate (mm) Length of 6-bolt fishplate (mm) Diameter of bolt holes in fish plates (mm) Calculated weight per pair (4 hole) (kg) Calculated weight per pair (6 hole) (kg) BS50 “O” 406.4 609.6 20.64 6.68 10.14 BS60A 406.4 609.6 20.64 9.84 14.76 BS60R 406.4 609.6 20.64 8.75 13.14 BS70A 406.4 609.6 ...

  Rail Spikes for sale from China Rail spikes are also called railroad spikes. it is a  clip for fixing rails  in railway systems. It fixes the rails to the sleepers to ensure the vertical fixation of the rails. At the same time, together with the sleeper system to ensure the fixation of the gauge, it is an important accessory of the rail installation system. Rail nails come in various shapes for different functions. The material for the production of railway spikes can be carbon steel or stainless steel as required, and the surface of the spikes can be flat, black, hot-dip galvanized, galvanized, etc. Among various road studs, dog-shaped road studs and spiral road studs are the most common types. The railway dog spikes are used for wood rail sleepers. Glory rail do rail spikes for sale for many years. We produced rail spikes according to DIN/GOST/AREMA/GB/TB standards. The materials are mainly using low carbon steel, alloy steel, etc.  rail spikes ……………………………………………...

  6A-6 rail clips for P50 rails from China Gloryrail is a 6A-6 rail clips supplier from China, we could offer 6A-6, 6A-5, 6A-4,6-2. etc rail clips . 6A-6 rail clips are used for P50 heavy rails and QU100 crane rails. 6A-6 rail clip is a kind of small&exquisite pragmatic economic utility parts/fittings that is used to compact and fix steel rails with concrete/timber sleeper or I-beams or concrete beams. It is made of cast ductile iron, perfect quality, and surface treatment. It is widely used because of its easy installation and low cost. 6A-6 rail clips supplier In order to better serve the different needs of customers, our technical team is available to provide advice and support, helping every customer to optimize their rail selections to minimize life cycle costs. We supply suitable rail parts, like fish plates, rail clips, bolts, and nuts. We supply rail processing, like 45-degree miter cut, welding process, milling process, special profile processing, etc. Our engineer he...

  UIC54 rail joint bars supplier from China Glory Rail  can supply UIC standard fishplates joint bars for railway rails for rails connection. UIC54 rail joint bars are the joint bars used for the connection between UIC54 rails. UIC54 rail joint bar is a very common fishplate for rails. Because UIC (International Union of Railways) standard tracks are used broadly. So the demand for the UIC54 rail joint bar is high. Gloryrail has developed a mold for the mass production of UIC54 fishplates. We can be mass-produced. Advantages: Long service life Fast and easy installation Specification: UIC54 Standard Fishplates for Railway Rails uic54 rail joint bars .. We could also arrange production according to customers’ required drawings.  s…………………………………………………………………………………………………………………………………………………….. . …………………………………………………………………………………………………………………………………………………………………………………………… ……………………………….. After more than 20 years of unremitting efforts, the fish plate has become our company’s leading ...

  Double hole rail clamp for 43kg steel rails GDGL-2 rail clip is a kind of double hole rail clamp, designed to fix 43kg heavy rails. GDGL-2 double hole rail clamp is a two-hole pressure plate, which is a 43kg track fixture, 150*95*18mm long with a slope, and matching accessories include wedge-shaped backing plates, M-shaped backing plates, bolts, etc. The GDGL-2 track pressure plate complies with the 04G325 national standard (special size requirements can be customized according to the customer). Manufacturer’s phone: 18653422237. The GDGL-2 track pressure plate is used in industrial plants and missed trestle bridges with reinforced concrete crane beams or prestressed concrete crane beams. Materials and requirements for GDGL-2 rail clamp: 1. Steel plate The splint and section steel adopt Q235 steel (No. 3 steel), and its technical conditions are in line with national standards. 2. Hexagon head bolts should meet the requirements of <GB/T5780-2000>, hexagon nuts should meet ...

  TG38 Rail Clamp for  P38 rail  Supplier from China SWJK TG38  rail clamp  is a 38kg/m orbit welding type fixed part produced and sold by Glory Rail. It mainly includes a base, a press plate, an adjusting plate, and bolts. The SWJK-TG38 type rail press uses Q235 or Q345 steel castings, cast The standard of carbon steel, the surface roughness is allowed *6414-86M “casting size tolerance” CT6 level requirements; Supporting data of SWJK-TG38 rail clamp: Installation rail: 38kg/m lifting rail Material: cast steel Matching bolts: 8.8 grade Package Weight: 1.4kg Assembly process of SWJK-TG38 rail clamp: Bolt-in place-upper cover-flat washer-spring washer-nut-tighten. TG38 Rail Clamp Supplier Material and performance requirements of SWJK-TG38 rail clamp (1) The track pressure plate, fixed bottom plate and wedge-shaped adjusting plate adopt Q235 or Q345 steel castings, the standard of casting carbon steel, the surface roughness is allowed *6414-86M “casting size toler...

  TG43 Rail Clamp for  P43 rail  Supplier from China TG43 rail clamp is a kind of WJK rail clamp. WJK welded rail clamp, also known as track clamp, is a fastener used to fix rails during rail laying. It is also a welded rail fixture and is a widely used crane beam rail fixing standard. WJK welded rail clamps are divided into three categories: (1) Light rail clamps: WJK-TG24, WJK-TG30, (2) Heavy rail rail clamp: WJK-TG38, WJK-TG43, WJKTG50 (3) Lifting rail clamp: WJK-QU80, WJK-QU100, WJK-QU120 Supporting data of WJK-TG43 rail clamp: Installation rail: 43kg/m lifting rail Material: cast steel Matching bolts: 8.8 grade Package Weight: 1.4kg Assembly process of WJK-TG43 rail clamp: Bolt-in place-upper cover-flat washer-spring washer-nut-tighten. tg43 rail clamp installation WJK-TG43 rail clamp feature: 1. Ordinary welded rail clamp is a fixing device widely used between steel crane beams and rails in China. The material is usually divided into the following two types: Q235 m...