Skip to main content

1220 rail clips/7220 rail clips supplier from China

 

1220 rail clips/7220 rail clips supplier from China

Gloryrail is a 7220 rail clips supplier from China (it is equivalent to Gantrail 1220 rail clips ), it is a kind of welded base fixing clip with double bolts. designed to fix heavy rails.

It can withstand a horizontal force from the rail of 300kN(30.6 tonnes). its low profile allows it to be used with cranes that are fitted with guide rollers.

1220-rail-clips-drawing

1220-rail-clips-drawing

Save

The proven design has been used successfully for many years throughout the world.
• The clip is welded to the rail support. No access is required from below.
• The two main parts are locked together on tightening the grade 10.9 bolts.
• The clip has a self-tightening mechanism.
• A special vulcanized rubber block applies a controlled force to the rail.

Weldable clips are available in different sizes and capacities to suit different rail profiles and wheel loads. The correct clip selection not only depends on those dimensional and mechanical considerations but also on installation contingencies. We, therefore, recommend you contacting us to discuss your requirements.

Comments

Popular posts from this blog

30 LB RAIL FOR SALE

  30 LB RAIL FOR SALE What is a 30 lb rail? A 30 lb rail refers to a rail weighing 30 lb in meters, which is an ASCE 30 model rail produced according to ASTM A1. As a common light track, it is mainly used for laying mining track lines. Therefore, it is widely used in the South American market. The dimensions of the 30 lb rail are as follows: Head width: 42.9mm Track height: 79.4mm Track bottom width: 79.4mm Waist thickness: 8.4mm GloryRail is an important  mining rail  supplier in China. Engaged in rail supply for more than 20 years. Rail products are exported to many countries and regions around the world. Trusted and supported by many mining customers. We maintain long-term cooperative relationships with many important customers in Peru, Colombia, Panama, and Venezuela in South America BUY 30 LB RAIL FROM CHINA As the world’s most important rail tracks production base. There are six major steel mills in China producing rails with an annual output of millions of tons. G...

Welding Process of Overhead Crane Rail Joint

Welding Process of Overhead Crane Rail Joint In order to make the overhead crane rail transport more stable, rail splints will not be used for the overhead crane rail joint connection, but welded joint connection will be used. The main key to the welded joint is to solve the bending deformation and weld cracking of the overhead crane rail joint. During the welding process of the overhead crane rail joint, the overhead crane rail joint is deformed downwardly, so the overhead crane rail end must be padded to a certain height before welding to ensure that the rail joint can be kept straight after the welding is completed. The height of the rail end pad is determined by factors such as the type of rail, length, fixing method and ambient temperature. The rails are fixed to the crane beam by means of hook bolts, and each joint is provided with four fixed points. After the bottom of the rail is welded, reduce the height to 20mm, and then tighten the hook bolts to continue welding. When the o...

Study on the Influence of 40×60 Crane Rail Plate Stres

Study on the Influence of 40×60 Crane Rail Plate Stress The main operation mode of the overhead crane is the orbital operation, that is, the wheel supports the whole crane and transmits the gravity to the lower 40×60 crane rail , and the 40×60 crane rail receives the concentrated pressure from the crane wheel and guides the wheel to run. Therefore, the track device is the direct load-bearing structure of the crane device. Usually, special rails that meet the requirements of the wheels are used as crane rails. These rails are fixed with the pressure plate and the structure of the plant. If the crane runs at a slow speed, the operating frequency is not high, and the wheel pressure is not large, this solution can still meet the requirements. However, if the crane is in a high-speed, frequent or large-wheel working environment, the existing fixing method cannot meet the performance requirements. At this time, the phenomenon that the rail press plate bolt is broken is extremely likely to ...