Skip to main content

Crane Rail clips Standard

 

  • crane rail clips

    Crane Rail clips Standard

    Crane Rail clips Standard

    Crane is a special equipment with high risk, and its structural design, manufacture, and inspection all have national standard specifications, while the rail fixed pressure plate has no design or standard specifications. In the safety accidents of cranes, many are caused by the failure of the fixing of the crane rail clips. Therefore, the force and stress distribution of the crane rail clips are studied, hoping to provide a reasonable analysis method and design basis for the pressure plate.
    The force analysis of the track The bridge crane lifts the object with hooks, track pressure plate manufacturers grab or electromagnets, transfers the load to the wheels through the bridge frame, and contacts the track with the wheels, so that the load is supported by the track, track pressure plate, and support. Liang et al. spread to the ground. The force on the track is analyzed in three directions, namely longitudinal, lateral and vertical forces. When the crane is static, its track is only affected by its own weight, rated load, and the position of the center of gravity of the truss; when it is dynamic, it is affected by load lifting, starting acceleration, wheel tread is not round, track tread is uneven, and rail joints are undulating, etc., causing shock and vibration of the crane.

    Comments

    Post a Comment

    Popular posts from this blog

    30 LB RAIL FOR SALE

      30 LB RAIL FOR SALE What is a 30 lb rail? A 30 lb rail refers to a rail weighing 30 lb in meters, which is an ASCE 30 model rail produced according to ASTM A1. As a common light track, it is mainly used for laying mining track lines. Therefore, it is widely used in the South American market. The dimensions of the 30 lb rail are as follows: Head width: 42.9mm Track height: 79.4mm Track bottom width: 79.4mm Waist thickness: 8.4mm GloryRail is an important  mining rail  supplier in China. Engaged in rail supply for more than 20 years. Rail products are exported to many countries and regions around the world. Trusted and supported by many mining customers. We maintain long-term cooperative relationships with many important customers in Peru, Colombia, Panama, and Venezuela in South America BUY 30 LB RAIL FROM CHINA As the world’s most important rail tracks production base. There are six major steel mills in China producing rails with an annual output of millions of tons. G...
    Post a Comment
    Read more

    What is crane rail system

      What is crane rail system What is the Crane rail system? The crane rail system consists of rail,  rail clip , rail joint,  rail pad , and other rail accessories. Crane rail is a crane running route laid by steel rail, which can ensure that the crane runs along the specified line and transmit wheel pressure to the foundation. The rail is usually composed of two-wheel rails. The top of the rail is convex, and the ground is a flat plate with a certain width, which increases the contact surface with the foundation. The section of the rail is mostly I-shaped and has good bending strength. When the crane is running, the rail cannot move horizontally and longitudinally, and the rail should be easy to adjust. The fixed parts of rail and rail shall be free of crack, looseness, and corrosion; If there is any crack, it shall be replaced in time, and other defects shall be handled in time. As for the installation of the crane rail system, there are two kinds of rail beams commonly ...
    Post a Comment
    Read more

    Study on the Influence of 40×60 Crane Rail Plate Stres

    Study on the Influence of 40×60 Crane Rail Plate Stress The main operation mode of the overhead crane is the orbital operation, that is, the wheel supports the whole crane and transmits the gravity to the lower 40×60 crane rail , and the 40×60 crane rail receives the concentrated pressure from the crane wheel and guides the wheel to run. Therefore, the track device is the direct load-bearing structure of the crane device. Usually, special rails that meet the requirements of the wheels are used as crane rails. These rails are fixed with the pressure plate and the structure of the plant. If the crane runs at a slow speed, the operating frequency is not high, and the wheel pressure is not large, this solution can still meet the requirements. However, if the crane is in a high-speed, frequent or large-wheel working environment, the existing fixing method cannot meet the performance requirements. At this time, the phenomenon that the rail press plate bolt is broken is extremely likely to ...
    Post a Comment
    Read more